Back to: Rotary Arm Automatic

4100-45-OHA Titan Conveyorized Automatic

Print

Cousin's Packaging

Description

SPECIFICATIONS

Specification	Description
Production Speed	1-45 loads per hour NOTE: Process rates will vary with load size, number of wraps & forklift load/unload time
Load Capacity	Maximum load weight: 4,000 lbs dynamic – 12,000 lbs static Maximum load size: 50″ W x 50″ L (71″ max. load diagonal) x 80″ H (plus up to 4″ top overlap) Minimum load size: 30″ W x 30″ L x 24″ H
Rotary Arm	Double flange bearing support system Twin V-belt drive pulleys with belt tensioner 1-14 RPM rotational speed c/w soft start acceleration Final revolution deceleration and positive stop alignment 1/2 HP DC variable speed motor
Film Carriage Elevator	1/2 HP DC variable speed motor Direct flat belt drive system Maintenance free 12 point carriage guidance system
Film Delivery System	*NEW Super Rapid Thread ™ II* 20″ capacity pre-stretch film carriage Special Film Threading Device – Uniquely orientates the sticky side of the film against the pre-stretch rollers and the inside of the load. 1/2 HP DC variable speed motor Fully electronic dynamic dancer corner compensation 33 to 313% fixed stretch capability Pre-stretch ratio variable by easy sprocket change Rapid Thread ™ Safety Door with auto power cut-off switch Superior *film-to-roller* contact area Lifetime warranty on pre-stretch rollers
Power Roller Conveyer	Basic system includes: 5ft Infeed section, 11ft Process/wrap zone section and 5ft exit section Each section includes: Chain driven live roller conveyor rated 4,000 lbs per section 2-1/2″ diameter 11 gauge rollers c/w 11/16″ hex axles on 3″ centers All rollers ANSI #40 chain driven, roller to roller 54″ effective roller width Conveyor speeds 20 to 50 FPM (specify required speed) with electronic soft start Pass-line height – 18″ from floor to top of rollers 1/2 HP AC variable speed reversible TEFC motor on infeed & outfeed conveyors / 3/4 HP AC variable speed reversible TEFC motor on process conveyor Automatic load indexing and centering by photo-eye & PLC logic
Electrical Input Requirements	208Y/120 Volts 3 Phase 60 Hz 30 Amps (other voltages available – consult factory)
Pneumatic Requirement	3 CFM @ 80 PSI clean dry pneumatic supply required Filter/regulator c/w gauge & lock-out valve provided
Typical System Dimensions	252″ (L) x 148″ (W) x 157″ (H) (Standard includes Conveyors (L) and Control Panel (W) – all dimensions approximate)

FEATURES

Feature	Description
Automation Features	Pneumatically actuated film clamp mechanism Pneumatically actuated film tail cut/wiper arm mechanism Ni-chrome impulse hot wire film cut off c/w automatic periodic cleaning cycle
Control Features	PANASONIC FP-X Programmable Logic Controller (PLC) HMI Touchscreen Operator Interface Panel Illuminated Power Start / Reset button Emergency Stop button Wrap Cycle Start (rewrap) button Manual controls provided for rotary arm jog, film carriage elevator lower/raise, film clamp open/close and conveyors forward/reverse Wrap Bypass mode selector switch Separate film carriage elevator raise & lower speed controls Film tension (Force-to-Load) control Separate 1 to 12 revolution top & bottom wrap control Triple beam auto load height sensing photo-eye, detects dark or shiny loads Broken film/out of film detection c/w automatic machine reset and fault beacon light Rotary arm and film carriage elevator dynamic braking NEMA 12 control panel and junction boxes Dust tight slip ring assembly Non-proprietary UL/CSA approved components
Structural Features	All structural steel construction Structural tube machine tower & frame Electro-static powder coated paint finish
Safety Features	Personnel Safety – Rotary Arm Obstruction Emergency Stop Sensor Wire mesh safety barriers enclose the wrap zone to prevent personnel intrusion Operator Access Gates c/w Safety Interlock Switches disable machine operation when gate(s) opened Hard-wired emergency stop and operator access gate circuits with Category 3 dual channel safety relays